VHS VIBES 1.7.0 — the sound under the picture.
A VHS tape degradation effect for Akai MPC standalone hardware: pitch wobble, tape saturation, the Hi-Fi track, generation loss, noise reduction, hum, hiss, crackle, deck faults and a dry/wet mix, on a hot pink cassette with reels that turn.
hi-fi stereo
Type on the TAPE page has a third button: Hi-Fi. It is the FM sound the spinning video heads write under the picture: a real Hi-Fi deck's machinery, driven far out of spec, with the click amount given its own knob. The bottom of every knob is a deck in good order.
Hi-Fi does not saturate. It stays clean up to a hard ceiling. What gives it away is everything around the sound: hiss that rises and falls with the music, clicks when the signal off the tape is weak, a buzz when the heads hand over, and drops to the dull mono linear track when the signal is lost.
Three knobs on the TAPE page take new jobs:
| Knob | In Hi-Fi |
|---|
| Rec Level | -10 to +28 dB: how hard the sound meets the ceiling |
| Carrier | 0 to -20 dB: how strong the signal off the tape is |
| Cal | playback set to another level than recording: it pumps |
With the VIBE block's power switch on, the Hi-Fi track also takes over Hiss, Crackle, Head Buzz, Breathing, Tracking, Drift and Dropouts, and B-Type NR is ignored. Those ten controls and the HI-FI button turn sunset orange.
- Carrier down is more hiss. From about -14 dB the deck starts to fall to the linear track now and then, and from about -19 dB it hardly ever comes back. Each fall lasts about a quarter of a second, and the linear track brings its own hiss.
- Crackle is the amount of clicks, from none to 150 a second on each channel. Carrier does not move it; Drift, Tracking and Dropouts bring bursts.
- Drum hits after silence touch the ceiling even with Rec Level low. That is the format.
Five new programs: Hi-Fi - Clean Deck, Hi-Fi - Hot Signal, Hi-Fi - Worn Rental, Hi-Fi - Tracking Lost and Hi-Fi - Wrong Deck.
a tape from another deck
Azimuth, on the DECK page while Type is VHS: the linear track's head tilted against the recording, 0' to 60' (minutes of arc). The treble cancels across the tilted head: hollow, notched highs with a slow swish as the tilt wanders. A tape from another deck is 3' to 8', a knocked head 60'. EP is three times worse than SP, and B-Type NR on On makes the dulling worse. It rests at 0'.
Two new programs use it: VHS - Borrowed Tape and VHS - Wrong Deck EP.
the picture shows the sound
A new switch, Visual Vibes (DECK page, SCREEN block), turns the page sticker into a worn video picture of what the plugin is doing:
- the sun in the Type's shade: pink, mint or orange
- snow with the hiss
- a strip of noise along the bottom with Head Buzz
- a white streak at each dropout, a rolling band when the tracking is lost
- the grid bending with the wobble
- a haze as Hi Cut comes down
It is off in a new instance and in an older project. Animation stays the master switch, and the sound is the same either way.
On the label
- Somebody cleaned up the deck. Every section opens with its Power switch, the knobs that belong together sit together, and the blocks wear the names of what they do: VIBE, WARP, AGC, ALIGNMENT. The first Type, 2-Band up to now, answers to Simple. Same machine, easier to find in the dark. The Q-Links follow the screen.
- Tape Speed (Type on VHS) also names PAL SP, Beta II, PAL Beta, Beta III and PAL LP where their speeds fall. The sound at each position is as before.
- Whistle climbs faster above 60 %, to 15 dB more at the top. Up to 60 % it is unchanged.
- HQ now also covers the modeled microphones and the recording side of B-Type NR. Bright, loud sounds no longer fold back into the midrange there: the tape should not sound digital.
- 46 programs, 58 controls.
Projects made with 1.3 to 1.6.0 load with every setting in place and sound as they did, apart from that cleaner HQ and the louder top of Whistle. Azimuth rests at 0' and Visual Vibes off, and the 39 older programs are unchanged. One exception: automation of Type recorded in 1.5 or 1.6 stores only a knob position, and now reads the old VHS position as Hi-Fi.
Install
- Download
vhs-vibes-1.7.0-mpc.zip below and unzip it. - Copy the folder
anthonytheinventor - VST - VHS Vibes into a folder named VST2 Plugins at the top of a USB drive, an SD card or the MPC's internal drive (replace the old folder if an earlier version is there). - On the MPC: Preferences > Enhancements (Beta), switch on Enable Enhancements and External Plugin Support, then restart the MPC.
- Find it in the plugin browser under External Plugins.
Needs MPC OS 3.10.1 or later. Builds for 32-bit and 64-bit MPCs are both in the zip, with INSTALL.txt and the README. The manual, VHS-Vibes-Manual.pdf, is attached below; it has gone dark, for reading on a screen. VHS-Vibes-Manual-print.pdf is the same manual on white paper.
Or let Open MPC carry the tape for you: the armv7, aarch64 and sdk zips below are the ones its Plugin Manager and installers take.
the meter barely moves
Open MPC's CPU bench, on an MPC One+: 8.7 % of one audio block at the 99th percentile, 13.6 % at the worst. Verdict: PASS.
tip jar
VHS Vibes is free. If it ends up on your tracks, you can leave a tip at ko-fi.com/anthonytheinventor. It keeps the VCR running.
be kind ・ rewind